I said that decoration is a very laborious thing, no one should refute it? If so, it must have not been renovated in person. Just how to go about the decoration process , which step to take first, can make people dizzy.
There are countless things to regret after the decoration , but if you think about it, the problems in the decoration process account for most of the problems. Although the decoration process sequence is similar, in fact, some procedures can be flexibly selected.
Install the door first or lay the floor first?
Let me talk about the conclusion first. The most ideal way is to install the wood floor first by the master who installs the floor, leaving the part near the door.
But this operation is in reality ...
The two processes are in succession, the main points of contention.
â— The gap under the door is controlled at 5 ~ 8mm.
â— Whether the closing between the door cover and the floor is tight
â— Whether the closing between the door cover and the baseboard is neat and beautiful.
â— The installation process caused damage to the door or floor.
If the room is paved with floors and the walkway is tiled, you can install the door first without tangling. Because the tiles are laid earlier than the door, the height of the door already has a reference standard.
Special attention should be paid to: the type and specifications of the wooden floor are selected in advance, and the height and the floor reserved for the floor are confirmed after confirming the leveling of the room with the merchant. In addition, in general, laminate flooring is generally 15mm, solid wood multilayer is generally 18mm, and solid wood is keel 30mm, but the specific is still subject to consulting merchants.
We focused on the situation where there are floors inside and outside the door
[Make the door cover first]
advantage
â‘ The floor is not afraid of being smashed, stained, or flowered by the door or the tool accessories used to install the door. The space required to install the door is large, the process is "rough", the tools are heavy, and the foam rubber, glass glue, etc. are dirty.
â‘¡ The transition between the anchor line and the door cover can be done very tightly.
[Risks present]
â‘ The door cover cannot cover the expansion joint of the floor
Expansion joints should be left on the floor against the wall, and the skirting should be used to cover the edges. Since the door cover has been completed, it cannot be covered on the floor like an anchor line. It can only be closed with glass glue, depending on the detail of the master's construction. First install the door and only use glass glue to sew and close the edges
â‘¡ The gap between the door and the floor is difficult to control accurately.
The master who installs the door generally gives priority to ensuring that there are enough gaps to open and close the door, so as not to trouble you later, he may reserve a larger gap, but this is not the best visual or practical angle (poor sound insulation) is not the best select.
[Lay the floor first]
Basically the advantages and disadvantages are reversed
Advantages: â‘ The rear door cover can "cover" the expansion joint of the floor, which is better visually; â‘¡The door joint can be adjusted to the best on site.
Risks: â‘ Installing the door on site may cause damage to the floor. â‘¡The processing of the anchor line and the edge of the door cover may not be tight enough.
[Summary]
Lay the floor first: it is easier to close the edges, look better, and the door seams are more accurate
When installing the door, pay attention to the protection of the floor in place. You can leave the ground line at the door and do not install it first. Let the door installer help install it. Add some money or hand a cigarette to buy a drink and talk.
Install the door first: pay special attention to the communication with the master, and reserve the gaps of the lower edge of the door as accurately as possible; in addition, you can let the master who installs the floor pay more attention to the details of the door frame, or try to cut the wood into the shape of the door cover to leave the seam. Or suggest that the master put the floor under the door cover and start to lay
Paint the wall first or make the wardrobe first?
Let's talk about the conclusion first. The ideal is to scrape the putty for the first time, and then the carpenter enters the field to lay the ceiling, door frame, cabinet, etc., and then put the putty on the back two times.
But in fact, the master rarely can cooperate in this way, time is money, and the time to customize the wardrobe or carpentry may not be able to fully match your node.
The difference between the two processes mainly lies in the edge of the wall. To put it bluntly, it is actually a question of whether it can be beautiful in the end.
If you are a carpenter first, the back of the woodwork is cement. Some people worry that the cement wall will corrode the closet or the like. This is not necessary. If the other side of the wall is a place that may seep water, such as the bathroom and kitchen, just waterproof it If you do n’t do a good job of waterproofing, you scraped the putty and brushed the paint.
First scrape the putty and the wall paint, you can correct some unevenness of the cement wall (2 ~ 3mm), because the cabinets are horizontal and vertical, a little unevenness can be easily seen, and then putty will be filled in later If the master's skill is not good or is impetuous, it will make the edge of the edge more ugly or even have obvious black seams.
Please pay attention to remind the master to paste the separation paper and protect the film to avoid the wardrobe from being stained by paint and putty in the later period. That cleaning will be a nightmare. Most of the wasteland cleaning and cleaning have not done so meticulously for you. Clean yourself a little bit.
If it is a custom wardrobe after painting the wall paint, you will usually use glass glue to close the side of the wall, usually transparent or white glass glue. Here it is recommended to use a good glass glue, which is prone to yellowing if the quality is poor for a long time.
If the wall at home is not vertical, you can discuss with the custom wardrobe dealer, can you make a remedy for the side wall with the wall tilt, or use gypsum to fill the gap and then hit the glass glue.
So in general, there is not much problem with which advanced field, the first protection of the wardrobe should be done after the protection (the masking paper, protective film must be affixed), first paint or putty, the main wardrobe close The craft should be done well.
Install floor heating or hydropower first
If the developer comes with floor heating, install the water and electricity directly, and finally hang the boiler. If there is no built-in underfloor heating, hydroelectricity transformation is carried out first, and the mid-floor heating can be laid in the field together; or the hydroelectricity can be changed first, and then the underfloor heating is installed. Now some hydropower masters will install floor heating.
The above is just a small part of the decoration process, there are many similar problems, you can first understand in advance how to think about the decoration, sharpening the woodworker.
What, the decoration still uses his own money? ! The Qi family is decorated in installments, with an ultra-low annual interest rate of 3.55% and a maximum loan of 1 million. Apply now to enjoy the discount
If you are interested in brand cooperation, content cooperation, and advertising of this website, please send an email to :.
Ceramic Magnet,Ferrite Magnet,Ceramic Block Magnets ,Ceramic Ferrite Magnet
Ningbo Besten Magnet Co., Ltd. , https://www.bestenmagnets.com