The installation of doors and windows in the house is very important, because the doors and windows are the guarantee of our lives and property, so the installation of the doors and windows is particularly important, but after the doors and windows are installed, there will always be gaps, then you need to glue. So, the gap will not be strict, then what are the methods of glue the door and window? What are the skills of the door and window glue? The small series of the decoration home network below will take you to take a look.
First, the method of glue the door and window
1. When installing the window frames of each floor, the horizontal and vertical pull lines should be connected, and the layers should be horizontal and straight up and down. When the window frame and the wall are fixed, the upper frame is fixed first, the rear frame is fixed, and the plastic expansion bolt is used for fixing. The inner cavity of the expansion joint between the frame and the opening is filled with a closed-cell foam, a foaming agent and the like, and the surface is sealed with a sealant.
2. The installation of doors and windows must be firm. The number, position and buried connection method of the embedded parts must meet the design requirements. The fasteners used to fix each reinforced steel must be no less than three, and the spacing should be no more than 300mm. It should be no more than 100mm. When the doors and windows are installed, the ambient temperature should not be lower than 5 °C. The hole with the embedded iron piece shall be fixed by welding, or the base hole shall be firstly punched on the embedded part according to the fastener specifications, and then fixed by fasteners.
3. When the splicing material is connected with the brick wall, the two ends of the splicing material should be inserted into the reserved hole first, and then fixed with C20 fine stone shovel. The two window frames should be connected with the splicing materials. After the cards are connected, they should be tightened in two directions with fasteners. The spacing should be ≤400mm. The fastener tip and the gap between the splicing material and the window bar are sealed by a sealing strip. When the doors and windows are connected to the wall by the pre-buried wood brick method, the wooden bricks should be treated with anti-corrosion treatment.
Second, the door and window glue tips
1. When the window frame and the wall are fixed, fix the upper frame first, then fix the frame, and fix it with plastic expansion bolts. When installing the floor sash of each floor, the horizontal and vertical pull-through lines shall be used, and the layers shall be horizontally uniform and straight up and down. The inner cavity of the expansion joint between the frame and the opening is filled with a closed-cell foam, a foaming agent and the like, and the surface is sealed with a sealant.
2. The installation of doors and windows must be firm. The number, position and buried connection method of the embedded parts must meet the design requirements. The fasteners used to fix each reinforced steel must be no less than three, and the spacing should be no more than 300mm. Should not be more than 100mm; in addition to stainless steel, the reinforced steel, fasteners and hardware should be treated with corrosion-resistant coating.
3. The concrete opening should be fixed by nails or plastic expansion bolts; the brick wall opening should be fixed by plastic expansion bolts and should not be fixed at the brick joints; the holes with pre-embedded iron parts should be fixed by welding, or first The base hole is punched on the embedded part according to the fastener specifications, and then fixed by fasteners.
The installation of doors and windows requires skill, otherwise the gap will be very large, then the method of glue the door and window and the technique of glue the door and window. What do you want to know about this knowledge through the introduction of Xiaobian? If you still want to know more about decoration information, please continue to pay attention to the decoration home Internet cafe.
More related wonderful reading:
What is a door and window glue machine? Door and window glue machine use precautions
Ceramic wash basin is made of high quality ceramic material.It has variety of color like White,Black,Silver,Gold color with Polished and Matte finishing,Which can offer the modern and classical style for the bathrooom.
- Made of high quality glazed ceramic which will not stain,fade, and is scratch and abrasion,and chemical resistant.
- Round,square and oval shape ia available for the bathroom space.
- Balck white Silver Gold color wash basin cao offer modern,classical and luxury stlye for the bathroom space.
Ceramic Basin Art,Ceramic Sink Bathroom,Handmade Wash Hand Basin,Ceramic Wash Hand Sink
Foshan Castel IMP&EXP Co.,Ltd , https://www.foshancastel.com