The balcony is usually used for leisure and drying clothes. For the convenience of drying clothes on the balcony, most families install fixed drying racks on the balcony. Here is a brief introduction to introduce the installation precautions for the balcony ceiling drying rack and what is the installation method of the balcony ceiling drying rack. I hope that everyone can understand the balcony ceiling drying rack through the following small series.
First, the balcony ceiling drying rack installation notes
1. Most of the modern family balcony ceilings are made of aluminum gussets or pvc gussets. Generally, they are about 10cm away from the ceiling of the balcony. In this case, the automatic lifting racks need to be installed.
2. It is understood that the automatic lifting drying rack is fixed by the ceiling of the ceiling with the expansion screw, and the balcony ceiling itself does not have a large bearing capacity. Therefore, if the ceiling is suspended from the balcony, the automatic lifting drying rack should not be directly fixed on the ceiling keel. The good installation method is to directly fix the steel wire on the ceiling floor through the ceiling ceiling decoration;
3. If it is a duplex structure or a balcony of a villa-type house, the height is higher than that of an ordinary house. When the consumer purchases, try to agree with the merchant to make an actual measurement, and then confirm the height of the wire of the automatic lifting rack to avoid the clothes bar being too high to be touched. And other issues.
4. It is necessary to pay attention to the selection of the position of the hand-cranked device. Determine the position before installing the drying rack, and it is not easy to get in the way. The general installer will also give you some advice. Once the installation is complete, it is not just that the hand crank is moving. Also have to plug holes and so on.
Second, the balcony ceiling drying rack installation method
1. When installing the balcony ceiling drying rack, when installing the top seat, we need to know the relevant diameter of the balcony lighting, and then wait for the installation mark between 15-30 cm on both sides, then measure the number and balcony edge. The distance, then more distance to determine the top of the top seat installation, and then measure the length of the balcony centered on the lamp, and then determine the distance between the sides of the lamp by 80-100 cm according to the length of the clothes hanger, and then measure the distance from the width. There are four intersections, which are the mounting locations for the top of the hanger.
2. After the position is determined, start drilling with the electric drill, and then fix the four top seats with the expansion screws first. You can adjust the length according to the length. The two top seats on the side of the hand corner are the movable end. The two top seats are fixed seats. The difference between the two is that they are connected to the movable seat. The movable seat must be installed in front.
3. The next step is to install the corner of the balcony drying rack. The corner can be installed on the top of the balcony or the top of the wall. The corner is 50-70 cm away from the movable top, but it must be triangular in the middle of the movable top. The position maintains a uniform vertical line, and friends who don't understand this can refer to the drawings.
4. In the drying rack, there is a steel wire. You can take out a steel wire first. First pass one end of the steel wire through the bearing wire groove of the corner, then pass through the movable wheel shaft wire groove of the movable top seat, and then pass through the fixed wire. The bearing wire groove of the end seat is perpendicular to the ground, and then the top cover is inserted from the wire.
5, as for the second wire to wear, similar to one, at each head of the wire to wear a ball, knotted inside the ball, and then pull the ball to the top seat, in Ding Hao screws, and finally install the plug on both ends of the drying rod.
Through the brief introduction of the above article, I believe that everyone has already had a certain understanding of the installation precautions for the balcony ceiling drying racks and the installation steps of the balcony ceiling drying racks. I hope that these small series can help you to meet the needs. Install the drying rack family. If you want to know more, please continue to pay attention to our decoration home network.
More related wonderful reading:
Types of floor drying racks
How much is the price of the drying rack? 2017 latest drying rack price list
What accessories do you need for the drying rack? Drying rack basic accessories
What is a fully automatic drying rack? How to choose a fully automatic drying rack?
What is the principle of automatic drying rack? How to install an automatic drying rack?
Mesh Sieve,Liquid Test Sieve,90 Micron Sieve,Copper Test Sieve
Xinxiang Xin Ming De Machinery Co., Ltd. , https://www.xmdsieve.com