When people decorate the ground, they often use tiles as the main material. The high-quality tiles can not only achieve better decorative effect, but also easier to clean and maintain. However, the use of ceramic tiles to decorate the ground also has a drawback, that is, the need to grasp the construction skills, or brick and brick gap is uneven, affecting the appearance. US grout is a kind of material that people often use to fill gaps. How many square meters can one do with a bottle of US grout? US grout construction methods and precautions what? The following Xiao Bian will share with you on these issues and look forward to helping those in need.
US grout bottle can do a few square
Everyone in the renovation will encounter a variety of problems. For example, a bottle of US grout can do several squares, this is no absolute answer. This is due to the fact that the sizes of the US sizing agents sold in the market are different, and the size of the gaps in the tile in each person is different. Therefore, this amount is difficult to estimate. Nowadays, people use the most commonly used 310ml cans of US grout, for the 800 * 800mm specifications of the floor, usually a can of US grout can be painted 22 square meters, for the 600 * 600mm floor, a can of 18 square meters, and For a 300*450mm floor, a tank can coat 13 square meters, a tank of 300*300mm can coat 11 square meters, a small floor of 100*100mm, and a tank can only coat 4 square meters (for reference only)!
US grout construction methods and precautions
US grout is a common material used by people to decorate the ground. Usually, everyone hires a master to help with construction. In fact, the construction of the US sizing agent is not difficult, and everyone can learn the method through learning: Leave a gap of 1 mm. Prior to the construction of the US Grout, first clean the magazine with dust or fine dust. Apply textured paper on both sides of the seam. The textured paper should be about 0.5mm from the edge of the slit. Put the US sizing agent on the glue gun and evenly press it along the seams. The construction is about 1 meter or so. Immediately use a finger or a small scraper to apply evenly. When the USG does not solidify (approximately 1 meter), remove the textured paper.
US grout construction methods and precautions
The construction of the US sizing agent seems to be very easy. There are just a few simple steps. However, there are a lot of details that need to be taken care of. If not, it will affect the final construction results. Everyone should pay attention to the following matters during the construction of US grouts:
1. Everyone should try their best to choose sunny and relatively high temperature weather construction, the temperature is usually 5 ~ 35 is better, please do not use it outdoors on a rainy day.
2. Everyone should clean the tile floor before construction: Clean the dust inside the gap of the tile, make the vacuum cleaner or sweeper clean, and need to ensure that the tile gap is not damp; no dust, particles.
3. We should also take care of the order of the construction of beautiful grout: first horizontally and vertically, clean the tiles on both sides of the gap groove to expose the tile edge on the line; pay attention to the intersection of tiles need to clean; tile gaps need to ensure clean, dry; if not clean If it is wet, the US sizing agent will fail to work. Before the US sizing agent is applied, it is necessary to apply a textured paper to the tile surfaces on both sides of the gap in the tile. The textured paper should be parallel to the brick seam. .
4. Everyone should pay attention to the discharge port to prevent jetting to the ceiling and wall when opening the US sizing agent. The width of the discharge nozzle should be consistent with the width of the slot so that the fabric can completely cover the bottom material.
5. If you are a novice, it is recommended to play 20cm-50cm; gradually become skilled, can play a longer length, when the gun is to be put flat glue gun, under the discharge mouth with a pick board to catch; when filling The material needs to be even and easy, not much, note a section of 1m long and immediately level off, can not be scraped after a period of time, the United States and the surface of the seam on the surface of the lack of US seam can be added to clean up.
6. In the case of a small brick with multiple cross joints, the principle of applying vertical seams first and then horizontal seams should be followed. When a cross point is encountered, the post-injection USG will scrape here to scrape the light and allow the seam to sew. Less agent flows into intersecting seams. The width of the cross joints should be the same, should use plastic cross positioning, or affect the appearance.
7. During the construction of the US trowel, it is necessary to remove the masking paper immediately after the trowel is applied. For a long time, it is easy to uproot the US sizing agent in the seam. It is worth noting that each time the material is turned on, the discharge port is sealed with tape to prevent flash waste. When re-stitching, the discharge nozzle has a little self-extinguishing material and can be erased with newspapers.
The above is about the United States and how to do a few squares and how to do the United States grout construction methods and precautions related to sharing, although the US grout occupied a very small area, but its construction is directly related to the quality of the ground appearance , we can not deal with sloppy oh! If you have more related issues, welcome to continue to pay attention to this site, and later will show more exciting content for everyone.
The product is prepared from a high quality Lubricant Additive Component detergent, TBN Booster Calcium Sulfonate, high molecular weight Ashless Dispersant , Corrosion Inhibitor ZDDP , High Temperature Antioxidant. And it has the advantages of excellent high-temperature detergency, low-temperature dispersion, anti-corrosion resistance and abrasion resistance. It can meet the performance level requirements of different diesel engine oil API requirement, and has good compatibility with Group II ,III Base Oil and Synthetic Base Oil .
HDEO Diesel Engine Oil Additive Package
Hdeo Additive,Hdeo Diesel Engine Oil Additive Package,Engine Oil Additive Package,Vehicle Engine Oil Additive Package
Zhengzhou Chorus Lubricant Additive Co.,Ltd. , https://www.cn-lubricantadditive.com