Duplex staircase installation pays attention to space saving

With the increase of living standards, people's requirements for materials are also increasing. The first thing for people with economic conditions should be to buy their own buildings. Now the duplex building is becoming more and more popular, and the style is novel. The design is simple and generous, and has become a good choice for people to consume.

The most common thing in the composite building is the stairs. In fact, the stairs are a relatively space-consuming thing. If the design of the stairs is unreasonable, the space is smaller, so how to install the double-stairs is especially important. Today, teach you how to install a double staircase to save space.

First, the installation method of single beam finished staircase

(a) Installation of the stair skeleton:

1Recheck the height of the stairs to see if it matches the height of the drawing.

2 Determine the position of the stairs and the base, and the L-shape must also determine the detailed position of the support or wall support at the turn.

3 After fixing, fix the hanging and the base

(2) Installation of stair treads

1 Take out the tread plate, determine the installation position of the stair tread plate, install it step by step from top to bottom, adjust the height of the small support with small step support, and then connect the small support to the tread plate without fixing it.

2 Fix the tread plate first and then fix the small support.

3 each step is operated as above

(iii) Installation of stair railings

1 first determine the position of the column to be installed, and install the column

2 fixed column base, the top fittings are loosened, and the wire and armrests are installed.

3 After the wire and armrests are installed and adjusted to the most suitable position, fix the screws on all the fence posts.

Second, the installation method of the neck finished finished staircase

(1) Installation method of the stair skeleton:

1Recheck the height of the stairs to see if it matches the height of the drawing.

2 Determine the position of the stairs and the base, and the L shape must also determine the detailed position of the support or wall support at the turn.

3 Place the constricted keel of the loose parts on the ground. According to the size of the drawing, the keel of the stair that is connected with the drawing will be set up according to the requirements, and the top wire will be fixed until it does not swing back and forth.

4 Lift the set necking skeleton to the installation position according to the drawings, and fix it with eyes.

5 adjust the skeleton level until the best after fixing the screws

(2) Installation method of stair treads

1 Remove the tread plate, determine the installation position of the stair tread plate, install it step by step from top to bottom, adjust the height of the small support with small step support, and then connect the small support to the tread plate without fixing it.

2 Fix the tread plate first and then fix the small support.

3 Steps are operated as above, and finally all screws can be fixed and tightened.

(3) Installation method of stair fence

1 first determine the position of the column to be installed, and install the column

2 fixed column base, the top fittings are loosened, and the wire and armrests are installed.

3 After the wire and armrests are installed and adjusted to the most suitable position, fix the screws on all the fence posts.

Third, the installation method of the spiral staircase

(1) Rotating staircase skeleton - installation method of pallet:

1 Re-check the height of the stairs to see if it matches the height of the drawing.

2 Determine the installation position of the column in the spiral staircase, the connection position of the upper suspension, and measure whether the distance between the middle column and the two walls matches the drawing.

3 Place the rotating stair tray of the parts on the ground. According to the size of the drawing, the stair keel that is connected with the drawing will be set up according to the requirements, and the top wire will be fixed.

4 Insert the set of rotating stair tray into the middle column tube according to the drawing requirements, and guide the last section to the fixed tray of the wall.

5 Adjust the orientation of the rotating stair tray until the balance is coordinated

6 Fix the top wire in the rotating stair tray and tighten until the tray does not shake.

(2) Installation method of stair treads

1 Remove the tread plate, determine the installation position of the stair tread plate, install it step by step from top to bottom, adjust the height of the small support with small step support, and then connect the small support to the tread plate without fixing it.

2 Check the adjustment overlap position and check whether the overlap data between each tread plate meets the design requirements.

3 After the correct error, the tread plate that fixes the rotating staircase

3 Steps are operated as above, and finally all screws can be fixed and tightened.

(3) Installation method of stair fence

1 first determine the position of the column to be installed, and install the column

2 fixed column base, the top fittings are loosened, and the wire and armrests are installed.

3 After the wire and armrests are installed and adjusted to the most suitable position, fix the screws on all the fence posts.  

Auto Parts

Precision Casting,Stainless Steel,Auto Parts

Gaomi Gongji Precise Metal Co., Ltd , http://www.preccastings.com