How to prevent internal paint contamination in furniture paint booth

In order to keep the air in the furniture booth clean, various types of paint booths are equipped with filtering devices, such as filter cotton, to filter the dust entering the air in the paint booth, and the ventilation system of the paint booth will have a paint room Adequate ventilation speed to ensure clean air in the paint booth. In many cases, the pollution of the paintwork on the body is caused by human factors. For example, the vehicle to be painted does not enter the paint booth without thorough cleaning, or the painter does not wear special protective clothing, or the paint room is not clean.
(1) Parts and paint cans should not be placed in the paint booth, because these things will accumulate dirt and eventually contaminate the vehicle to be sprayed. Items such as spray guns, paper tape, putty, clothing, and overalls should not be stored in an open environment. These items should be placed in a closed and ventilated storage room.

(2) After each painting work is completed, the floor and wall of the paint booth should be cleaned, and the coverings and other items used when covering the body should be cleaned up. When painting, try to cover the body with a disposable cover. Try not to use cotton to cover the car and the wheel cover, because the car is easy to collect dust.

(3) The vehicle to be sprayed is usually the largest source of pollution in the paint booth. Wheels, bumpers, and engine compartments collect large amounts of contaminants, and thorough body cleaning can reduce the impact of these contaminants on painting operations. Therefore, good preparations such as body cleaning are very important.

(4) Work clothes worn by paint operators are also important sources of pollution. In many repair shops, the work of polishing putty and painting paint is done by the same person. Many workers wear the same overalls when applying putty and spraying paint. This is not correct. It should be used when spraying paint. Work clothes. In the paint booth, you should wear a non-fiber off work clothing, rubber gloves, protective mask and respirator, and keep this wear when spraying each paint surface. Persons who do not wear special overalls are strictly forbidden to enter the paint booth, but can only view the painting work from the window to avoid contaminating the paint.

(5) In addition to covering the body and spraying work that must be done in the paint booth, other body preparation work and paint preparation work should be carried out outside the paint booth. Some repair shops even clean the vehicle or grind putty in the furniture paint booth http://, which is a serious violation of the refinishing practices.

(6) Spray equipment such as spray guns should be kept clean. The spray gun should be cleaned in time after each spraying operation to prevent the paint in the spray gun from drying out. After the paint dries, it will condense into pieces. If the dried paint flies out during spraying, defects will form on the paint surface.

(7) When the paint booth is working, the ventilation fan draws in the outside air, blows down the filter cotton on the ceiling of the paint booth, and the air is drawn out of the paint booth on the floor of the paint booth, and the airflow is created in the paint booth. In this way, even if there is a small amount of dust in the paint booth, it will not fly. The filter cotton on the roof of the paint booth can filter out most of the dust to keep the air in the paint booth clean. Therefore, the filter cotton on the ceiling of the paint booth and the absorbent cotton on the floor of the paint booth should be replaced regularly.

We manufacture a variety of refractory Metallized ceramics , mainly including Metallized Ceramic Insulator, Metallized Ceramic Tube, Metallized Ceramic Ring, Metallized Ceramic Substrate, Ceramic metallized cylinders.These Metallized Ceramics is fit for high vacuum, high voltage and high pressure applications due to their exceptional insulation strength, superb bonding strength and excellent metal to ceramic joining hermeticity. 

We offer a selection of metallization types to meet special needs via screen printing, pad printing, brushing, the regular types as below:

●Ceramic body base + Molybdenum (Mo/Mn) metallization.................●Ceramic body base + Silver(Ag) plating

●Ceramic body base + Tin (Sn) plating.................................................●Ceramic body base  + Molybdenum (Mo/Mn) + Nickle plating

●Ceramic body base + Tungsten (W) + Gold plating........................... â— Ceramic Substrate + Copper(Cu) plating. 

Based on in-house comprehensive manufacturing equipment from shaping to electroplating process, we have prototyping to high volume production capability. It helps us to make the dimensions consistency very well, also, helps us to offer a more competitive cost to our customers. Whatever, a very small trial order for R&D program, or extremely high volume need for cost down, we will find a optimal solution there to meet your needs.

These metallized ceramics are widely used in ceramic to metal, ceramic to ceramic joining technology in electrical, electronics, high vacuum technology, medical technology, sensor technology, the typical application like the ceramic insulator/body in vacuum interrupters, vacuum capacitors/thyristor, gas discharge tube, electron tubes, current feedthrough, X-ray tubes, power switches and so on.

Metallized ceramics

Metallized Ceramics,Vacuum Device Ceramics,Vaccum Tight Ceramics,Vacuum Ceramic Component

Jinghui Industry Ltd. , http://www.ceramictek.com