More and more 80s are not willing to replace the whitewashed wall with the wallpaper. In addition to the existing decoration, the wallpaper has rich colors and variable factors, which can add creativity and imagination to the monotonous icy wall. . The next Xiaobian will take you to see the contents of the selection and pasting methods of the wallpaper . I hope to help you.
First, the choice of wallpaper
Look: Look at the surface of the wallpaper for color differences, wrinkles, and bubbles. The wallpaper's flower pattern is clear and uniform.
Touch: After watching it, you can touch the wallpaper by hand and feel whether its texture is good and whether the thickness of the paper is the same.
Rub: You can cut a piece of wallpaper, wipe the paper with a damp cloth to see if there is a phenomenon of decolorization.
Wen: This is very important. If the wallpaper smells, it is likely that the content of volatile substances such as formaldehyde and vinyl chloride is high.
Second, the wallpaper paste method
1, first of all measure the size of the wall.
2. Eradicate the wall: remove the original paint, wallpaper and other objects on the wall. If there are cracks or potholes on the wall, use gypsum powder to replenish these areas and put a bandage on the surface; if there is a dusty wall or a partition wall, stick a glass cloth or a good cloth; some poor quality partitions Or to achieve the insulation effect of the external wall, full nail plasterboard.
3, cut decorative wallpaper: measure the height of the wall to the baseboard, and then cut the wallpaper. Don't add 10 centimeters to the wall height of the flower wallpaper, use it for trimming the edges; need to consider the symmetry of the pattern, need more than 10 centimeters, and from the top should be on the flower, plan after cutting, numbering, So you can paste them in order. In addition, the cut wallpaper should generally be soaked in clean water for 10 minutes before brushing.
4, brush base film greasy: brush the bottom film, the base film even brush on the wall, the thickness of moderate; scraping putty, polished. Two batches of scraping putty on the wall. After the putty is air-dried, use a sandpaper to polish the wall surface, remove uneven granules, make the wall smooth and flat, and use the base film to evenly paint the wall (cover paint), without being too thick. This will prevent the walls from absorbing the wallpaper glue, sticking the wallpaper on the wall and making the walls even.
5, brush glue, in order to ensure a solid paste, decorative wallpaper on the back and wall should brush, glue to brush uniform, can not be wrapped, from the heap, to prevent soiling wallpaper. Gum on the wall, the width should be 30 mm wider than the wallpaper. After brushing on the back of the wallpaper, the glue is placed on the face and folded for 5 minutes. It can prevent the glue surface from drying out quickly and is not easily contaminated.
6, cut decorative wallpaper. Before cutting, it is necessary to measure the length. The standard wallpaper is 10 meters long and 0.52 meters wide. It can store 5.2 square meters. The other two specifications are 7 square/roll, 16 square/roll.
7, paste: The principle is the first vertical level, first up and down, first high and low. When affixing the first piece of paper, look for a reference line at the corner of the wall, gently press down from the top to the bottom, from the center to the sides, and scrape with a scraper to make the wallpaper and the wall stick. When affixing the second wallpaper, overlap with the overlap of the first paper web by 20 mm, divide the overlapping portion with a wallpaper knife, remove the remaining portion, and scrape with a scraper. It should be noted that the glue that is squeezed out of the wallpaper should be wiped clean with a wet towel in time to prevent the wallpaper from turning yellow.
Xiao Bian concludes : The selection and pasting methods for wallpapers are introduced here for everyone. We hope that the above information will help everyone. If there is anything we do not know where to leave comments on the bottom of the page, we will answer your questions as soon as possible.
Wallpaper brand new section wallpaper European style wallpaper
1. Cobalt alloys have higher melting points than nickel (or iron) alloys ,This gives them the ability to absorb stress to a higher absolute temperature .
2. Cobalt alloys give superior hot corrosion resistance to gas turbine atmospheres , this is due to their high chromium content.
3. Cobalt alloys show superior thermal fatigue resistance and weldability over nickel alloys .
---Excellent wear and corrosion resistance even at high temperature up to 800℃
SYTOP cobalt base alloys is a range of cobalt-chromium-Tungsten Alloys with wear resistance, corrosion and high thermal resistance. It is widely used in oil & gas, machinery, wood cutting, automotive, paper and food processing industry etc.
Wear Resistant Plate,Cobalt Chromium Alloy Sheet,Steel Wear Resistant Plates,Cobalt Based Alloy Plates
Shenyang New Industry Co.,LTD , https://www.topcobalt.com