【Decoration knowledge】Construction and reinforcement methods

Some homes have been used for a period of thirty to four decades. Many homes have problems of one kind or another due to improper use and maintenance or construction quality. Some are quite serious and endanger structural safety. Due to the large investment in civil construction, despite the existence of some problems in the housing, it will not be demolished and rebuilt. With the method of structural reinforcement, as long as a small amount of investment is spent on maintenance and reinforcement, the bearing capacity can be restored. The following small series for everyone to introduce the transformation of housing reinforcement method Daquan.

1. Reinforcement method

The overall reinforcement is divided into two categories: one is direct reinforcement and the other is indirect reinforcement. Which is divided into many methods, Xiao Bian all to everyone listed below.

2, increase the section reinforcement method

The method has simple construction process, strong adaptability, and mature design and construction experience; it can be used for concrete reinforcement of beams, slabs, columns, walls and structures; but the long operating time has a certain impact on life or production. , And the reinforced buildings have a certain impact on headroom.

3, concrete reinforcement method

This method is similar to the advantages of the enlarged section method, and it does not affect the gap of the reinforced structure, and it does not have the disadvantage of long wet construction time; it is suitable for serious defects of low-strength concrete or reinforced concrete bearing elements beams and columns.

4, outsourcing sticking steel reinforcement method

This method is also known as the wet layer reinforcement method, the construction is simple, the workload is small, but the amount of steel is large, and should not be used in places where the temperature is not higher than 600°C in an unprotected place; Significantly increase the cross-sectional dimensions of the original component, but it is required to greatly increase the bearing capacity of the reinforced concrete structure.

5, paste steel plate reinforcement method

Rapid construction, on-the-spot non-wet operation or wet operation of gypsum, has little impact on production and life, and there is no obvious effect on the gaps that reinforce the original original structure appearance, but the reinforcement effect depends to a great extent on the glue technology and operation level; Suitable for bending tensile members that withstand static and normal humidity conditions or rebar.

6, winding method

The advantages and disadvantages of this method are similar to those of the enlarged cross-section method, and are not suitable for the bearing capacity of a reinforced concrete structure with an oblique cross-section, or where a combination of lateral pressure members is required.

7, anchor bolt method

This method is applicable to concrete strength concrete load-bearing structure for the transformation of C20 ~ C60, reinforcement; not applicable to the above-described structure and lightweight severe weathering.

8, rust-proof rust-proof reinforcement method

It is mainly used for the corrosion of steel or the conditions of use of old buildings under new buildings, and the prevention and prevention of rusted steel original expansion structure technology.

Editor's summary: The complete method for the reform and reinforcement of houses is introduced here. I hope to help everyone. If you want to know more related information, you can pay attention to this website information.

House Decoration Effect Drawing Encyclopedia Decoration Materials Knowledge House Decoration Notes House Decoration Effect diagram Decoration Daquan

A Noise Barrier (also called a soundwall, sound berm, Sound Barrier, or acoustical barrier) is an exterior structure designed to protect inhabitants of sensitive land use areas from noise pollution. Noise barriers are the most effective method of mitigating roadway, railway, and industrial noise sources – other than cessation of the source activity or use of source controls.

Specification of sound barrier:
1.Material: PC Acrylic board, plastic panle, steel sheet or aluminium sheet
2.Inner material:Glass wool
3.Sheets thickness:0.8-1mm, can be customized
4.Panel size:Width-500mm, Length2000mm, can be customized

5.Packaging Detailssteel pallet and plastic film

Material

Width

Length

Thickness

Acrylic board :PE PMMA resin
Frame material : Aluminum Alloy

 

100mm-1500mm

 

2000-2500mm

8mm-10mm


Frame: 70mm-100mm

Metal sheet :aluminiun steet or galvanized steel sheet

Inner Material:Glass wool

 

 

500mm-1000mm

 

 

2000mm-4000mm 

 

 

70mm-100mm

Sound Barrier

Sound Barrier,Sound Barrier Construction,Construction Sound Barrier,Road Sound Barriers

Anping shengsen metal wire mesh products co,. ltd , https://www.apshengsen.com