There is a seam in the wall of the furniture? The side of the cabinet is high and low... These are the problems that may occur after the furniture is installed. Recently, Mr. Zhang was very troubled by the installation of furniture, and called the editorial department of Jinghua Home to “sueâ€. So, is there any specification for furniture installation? How big is the door seam is reasonable? How to avoid various problems? Please refer to the advice of the professional installer.
Case
The cabinet has an obvious seam
Mr. Zhang's home is a small apartment. Since there is no bookcase, he has to find a custom furniture brand to customize a bookcase in the TV background wall area. In addition to display and storage, TV and air conditioning are also planned. After the workers finished the furniture, Mr. Zhang found that the upper cabinet and the lower cabinet were misplaced, there was no alignment, and the two sliding doors were not tight. He immediately asked the workers to debug, the workers thought it was a design problem, and promised to send someone to repair.
After a few days, the maintenance workers came to see it. The denial was a problem of design, but caused by uneven ground. So he added a gasket between the cabinets. Mr. Zhang found that the sliding door could basically be closed, but the situation of the wrong position of the upper and lower cabinets was not solved, and the gap between the cabinet and the cabinet was larger after the gasket was placed. Mr. Zhang accepted this plan in consideration of the fact that both people ran two times.
After half a year, Mr. Zhang suddenly found that the misplacement of the upper and lower cabinets was more serious, and there were gaps in other positions of the cabinet. He once again found a furniture manufacturer to request home repairs. At this point, the maintenance workers and designers came to the door, and once again, they thought that the seam was improperly designed, and a piece of partition was missing, resulting in uneven bearing force. Because it has been a long time, it is not easy to return to the factory, only to do some post-processing. Mr. Zhang had to give up, but he accepted it.
Improper measurement is the most problematic
The reporter interviewed several people in the brand furniture installation department. They said that since most of the panel furniture and solid wood furniture are finished furniture, they are also mechanically produced and produced. The specifications are very standard at the factory, so there are few problems caused by quality during installation.
What are the main problems in the installation process? Experts say that it is most common to be unable to install due to improper measurement. Du Gang, the person in charge of the installation department of Yifeng Furniture, said that many homeowners have made on-site measurements when they have not finished renovation or have not finished renovation. At this time, the ground height and wall treatment have not been completed, and it is easy to cause the furniture to be delivered to the home. Found that it can not be installed, such as the cabinet is high, can not be transported upstairs after finishing the stairs. Since the two parties have signed a contract, if the furniture produced meets the size standards stipulated in the contract and cannot be installed, it may be caused by changes in the owner's home environment, such as the floor height caused by the floor covering, and the two parties can solve the problem according to the contract. . And because the data told by the owner is not necessarily accurate and standardized, experts remind that when buying custom products, the designer must be on-site to measure.
According to reports, many furniture can not be installed because the owners did not consider the switch device, cable box, socket, electrical appliances, background wall, heating cover and other factors, and the replacement of ceiling lamps into chandeliers may also bring furniture installation Actual impact. Professionals suggest that the owner must inform these items in advance so as not to cause regret. In response to this situation, some furniture manufacturers provide more detailed services. Yang Chengfu, head of the Top 100 Furniture Engineering Service, said that before installing the furniture, the workers will carry the corresponding tools. If the sockets and switch panels are blocked, they will be punched in the field to minimize the loss of the owner.
Installation failure status highlights
According to industry insiders, although the mechanized production of furniture is less likely to have quality problems, due to the difference in the level of worker installation and the various family environments, there are some problems in the installation of furniture, and some need to be adjusted accordingly.
1. There are seams between the door panels: The reporter consults the "General Technical Conditions for Wood Furniture" (GB-T3324-2008), and the column "Shape and Position Deviation" in the standard clearly states: "All slits (when not designed) ≦ 2 mm ". If the gap between the door panels is too large or the door joints are large and small, it is most likely caused by uneven ground. At this time, after using the infrared level meter, the professional gasket can be used to properly adjust the furniture.
2. The cabinet tilts forward or backwards: Generally speaking, the finished cabinets are all right-angled. This situation is also caused by uneven ground. It can be adjusted according to the degree of tilt.
3. There is a clear gap between the furniture and the wall, and the gap size is different: this is due to the wall is not straight, if it is custom furniture, the manufacturer will usually use the wooden strip to seal the gap between the cabinet and the wall. Live and choose the appropriate glass glue according to the color of the furniture, in order to be more beautiful. But if it is finished furniture, it can only be to tilt the furniture slightly to the wall.
4. Damping drawers are not easy to push and pull: Most of them are caused by uneven ground or improper debugging of workers, and can be debugged according to experience. Some may be that the plastic clip on the back side of the slide has burrs and the push-pull is not smooth. In this case, the problem can be solved after using for a period of time.
5. Sliding door slides by itself: If it is just after installation, most of them are caused by uneven ground, and the gasket can be added; if this happens after using for a period of time, it is very likely that it is used in the cabinet. The weights are unevenly placed, so let the workers readjust them.
It should be noted that some manufacturers will check the flatness and verticality of the ground and wall before installation, and make appropriate adjustments during installation according to the test results. The owner can also know the problem at the first time.
Installation has been tested
After the installation is completed, the owner can also carry out some tests on his own to find the problem and solve it in time. So what should you check?
1. Horizontal and vertical. All horizontal planes should be flat and all facades should be vertical.
2. For panel furniture, all gaps, such as the gap between the door panels, the gap between the drawers, and the gap between the cabinet and the cabinet should be within 2 mm. Solid wood furniture is required to be slightly lower due to its characteristics of shrinkage and swelling, but the gap cannot exceed 4 mm.
3. Damping the drawer and sliding the sliding door smoothly and smoothly, do not slide back and forth, and where to push the hand should stop.
There is also a problem with improper use.
According to the professional introduction, after the furniture is used for half a year, the original installed furniture will also have gaps, large and horizontal tilt, etc., which are mostly related to the user's use. For example, the sliding door of the closet is easy to slide to one side, and the clothes in the closet are unevenly placed, and one side is light and the side is heavy; the gap between a certain drawer and the previous drawer becomes large, and the weight placed in the drawer is too much. Caused; when the bookcases are placed on the book, because the book is heavy, the bookcase may also undergo some deformation. However, these problems are not serious, contact customer service staff to adjust the position of the hardware to solve.
Custom furniture needs more attention
During the interview, Yang Chengfu and Du Gang both said that the custom furniture is installed relative to the finished furniture, and the problem may be slightly more. Experts said that some owners will ask for "not reliable" requirements, such as punching holes in glass, etc., designers will also put forward their own reasonable suggestions to avoid gaps and misalignment due to uneven design due to design defects. Waiting for the situation. Experts suggest that even if you choose custom furniture, owners should pay more attention to the designer's professional advice.
If the furniture design is flawed, it will be reflected in the installation. The person in charge of the installation of several furniture brands said that if the problem is found at the scene, it will generally return to the factory and be reinstalled after the change; if the problem is not too big, The site can be solved in other ways, and can usually be dealt with after reaching an agreement with the customer.
Heat Gun,Air Heat Gun,Power Tool
Fenghua Jade Motor Co., Ltd. , http://www.goselectric.com