It's time to start talking about carpentry.
The most basic principle of carpentry is to make carpenters do less and do less. The reason is also very simple, that is, furniture made by woodworking cannot be compared with furniture made by furniture factories outside. The most affected is the sense of quality. Of course, the main thing is that there is no way to compare the inner East.
This is not to downplay the carpentry in home improvement, but to seek truth from facts. No matter from the process of work, or the meticulous degree of workmanship, it is the advantage of the furniture factory.
Furniture materials mainly include blockboard, density board, trimeramine board and veneer plywood.
Remember, blockboard is a material that needs to be used as little as possible, because the blockboard contains a certain amount of formaldehyde, which is the source of indoor air pollution. So try to buy blockboards that meet environmental standards. But even so, it is recommended to use less blockboard. Blockboards are generally used only in the grass-roots section. Such as door covers, window covers, etc. Many woodworkers like to make blockboards in furniture. Try not to! Everyone must communicate with the workers first before making furniture. Beforehand, what materials should be used in a good place, so as to avoid doing a good job to change them later. Therefore, if conditions permit, it is better to write in advance the budget of each major piece of furniture.
When it comes to writing certain important materials in advance in the budget, I would like to open a little talk. It is strongly recommended that everything that can be clearly written be written in the budget statement. Do not be afraid of trouble and sloppy, thinking that you can revise it later. Because once the budget was not clearly written out, it was only due to the renovation workers who had been glued. The material written in the budget should preferably include the brand, model, size, color, etc. The more specific, the better. For example, Continental's aluminum alloy gussets are flat and grooved (under the same conditions, flat plates are slightly more expensive). If you need a flat plate, be sure to specify it in your budget! To promote it, you must pay attention.
Closer to home, now do furniture materials, more use of MDF and melamine panels. Trihydroamine board, also known as double plywood, or furniture board, is a kind of board with white veneers on both sides. It is flat, relatively moisture-proof, and has a good quality. It is mostly used as a partition in cabinets, as well as kitchen cabinets and bathroom cabinets. Re-emphasize the fact that parts that can be made of trihydramine plates, such as the above-mentioned several cases, try to use tri-hydroamine plates, but do not use blockboards. Remember that blockboards should only be used at the base level.
MDF is also a usable material. Its flatness is very good. A variety of veneer plywood is often attached to the top of the MDF. It is a common plate that can be used with ease.
With regard to the problem of gypsum board, it is necessary to pay attention to TX.
My home is Lafarge's plasterboard. It is estimated that most of the current home improvement uses this type of plasterboard. It should be noted that the thickness of the plasterboard is different, such as 9mm, 12mm and so on. It is recommended that everyone use 12mm thick, the price is not much more expensive, but it is more solid. Again, it must be stated on the budget statement! Otherwise, nine out of nine will give you 9mm.
There is also a problem that is easy to overlook. When using the gypsum board, do not use too much stitching. This means that you can use a gypsum board where you can't use a few stitches. Maybe your house worker will tell you that the splicing practice is easier to save and do not listen to him. Once again, we must try our best not to stitch! Although, at the splicing site, the painter will use the straps beforehand to put in the putty, but no one can guarantee that there will be no problems (eg, cracking, peeling, etc.) in the future.
Although not splicing as much as possible, there are certainly places for splicing. At this time, it should be noted that the gap between splicing is also very particular. Not too much, not too small. For example, 1mm - 2mm is ideal. Because the gypsum board will have some expansion, there must be a gap in the splice!
Gypsum board is mostly used for ceiling, background and other decorative purposes, although it does not affect the normal use of the house, but directly related to the final decoration effect, you must not sloppy TX, found that the problem must be corrected, even if it is rework!
The most basic principle of carpentry is to make carpenters do less and do less. The reason is also very simple, that is, furniture made by woodworking cannot be compared with furniture made by furniture factories outside. The most affected is the sense of quality. Of course, the main thing is that there is no way to compare the inner East.
This is not to downplay the carpentry in home improvement, but to seek truth from facts. No matter from the process of work, or the meticulous degree of workmanship, it is the advantage of the furniture factory.
Furniture materials mainly include blockboard, density board, trimeramine board and veneer plywood.
Remember, blockboard is a material that needs to be used as little as possible, because the blockboard contains a certain amount of formaldehyde, which is the source of indoor air pollution. So try to buy blockboards that meet environmental standards. But even so, it is recommended to use less blockboard. Blockboards are generally used only in the grass-roots section. Such as door covers, window covers, etc. Many woodworkers like to make blockboards in furniture. Try not to! Everyone must communicate with the workers first before making furniture. Beforehand, what materials should be used in a good place, so as to avoid doing a good job to change them later. Therefore, if conditions permit, it is better to write in advance the budget of each major piece of furniture.
When it comes to writing certain important materials in advance in the budget, I would like to open a little talk. It is strongly recommended that everything that can be clearly written be written in the budget statement. Do not be afraid of trouble and sloppy, thinking that you can revise it later. Because once the budget was not clearly written out, it was only due to the renovation workers who had been glued. The material written in the budget should preferably include the brand, model, size, color, etc. The more specific, the better. For example, Continental's aluminum alloy gussets are flat and grooved (under the same conditions, flat plates are slightly more expensive). If you need a flat plate, be sure to specify it in your budget! To promote it, you must pay attention.
Closer to home, now do furniture materials, more use of MDF and melamine panels. Trihydroamine board, also known as double plywood, or furniture board, is a kind of board with white veneers on both sides. It is flat, relatively moisture-proof, and has a good quality. It is mostly used as a partition in cabinets, as well as kitchen cabinets and bathroom cabinets. Re-emphasize the fact that parts that can be made of trihydramine plates, such as the above-mentioned several cases, try to use tri-hydroamine plates, but do not use blockboards. Remember that blockboards should only be used at the base level.
MDF is also a usable material. Its flatness is very good. A variety of veneer plywood is often attached to the top of the MDF. It is a common plate that can be used with ease.
With regard to the problem of gypsum board, it is necessary to pay attention to TX.
My home is Lafarge's plasterboard. It is estimated that most of the current home improvement uses this type of plasterboard. It should be noted that the thickness of the plasterboard is different, such as 9mm, 12mm and so on. It is recommended that everyone use 12mm thick, the price is not much more expensive, but it is more solid. Again, it must be stated on the budget statement! Otherwise, nine out of nine will give you 9mm.
There is also a problem that is easy to overlook. When using the gypsum board, do not use too much stitching. This means that you can use a gypsum board where you can't use a few stitches. Maybe your house worker will tell you that the splicing practice is easier to save and do not listen to him. Once again, we must try our best not to stitch! Although, at the splicing site, the painter will use the straps beforehand to put in the putty, but no one can guarantee that there will be no problems (eg, cracking, peeling, etc.) in the future.
Although not splicing as much as possible, there are certainly places for splicing. At this time, it should be noted that the gap between splicing is also very particular. Not too much, not too small. For example, 1mm - 2mm is ideal. Because the gypsum board will have some expansion, there must be a gap in the splice!
Gypsum board is mostly used for ceiling, background and other decorative purposes, although it does not affect the normal use of the house, but directly related to the final decoration effect, you must not sloppy TX, found that the problem must be corrected, even if it is rework!
Entrance Decoration Children's Room Decoration Furniture Home Interior Decoration Windows White Furniture Cabinet Door Cupboard Door Cabinet Kitchen Cabinet Door Bathroom Ceiling Material Bathroom Door Size Bathroom Ceiling Bathroom Size Bathroom Door
Structural Pipe,Structure Tube,Carbon Square Tube,Square Steel Tubing
Torich International Co.,Ltd--The Steel Tube Maker , http://www.chinasteeltubepipe.com